Search
MENU
- • Editing multiple devices
- • Basic Blinds Setup
- • Blinds configuration wizard
- • Light switching
- • Lighting timer basics
- • Heating and Cooling modes
- • Power limiting
- • Notification on high temperature
- • Configuring hysteresis control via Equation smart rule
- • Equithermic regulation
- • PID Temperature regulation
- • PID Cascade
- • Regulation of Boiler Cascade
- • Using statistic values in smart rules
- • Integrate multiple Core control units
- • Safe Values
- • How to combine two daily schedules in one day
- • Simple thermostat with hysteresis
- • Simple Heating management using Weekly schedule and Presence switch
- • Dimmer limits
- • Grouping or linking devices together
- • Access control
- • Static IP address configuration
- • 2019.1 - release planned for Q3 2019
- • 2018.1
- • 2017.1 - Charts updated
- • 2017.1 - Blinds automation - Depth of sun rays
- • 2017.1 - Blinds automation - angle control update
- • 2017.1 - Replace module action
- • 2017.1 - Expose devices
- • 2017.1 – Daily schedule smart rule
- • 2017.1 - Permissions
- • 2017.1 - Double click and triple click
- • 2017.1 - Set to Automatic mode - "Push buttons event" smart rule
- • 2017.1 - Multi-value switch
- • 2017.1 - Core update from the app
- • Firmware changelog
Simple configuration using templates
In order to quickly setup a Modbus-compatible device, you don't need to know Modbus parameters and TapHome expressions.
Step-by-step guide
Open Menu → Settings → Hardware → Modbus RTU
- In
Terminals menu, set proper BUS connector, where your device is connected. If there is no BUS available, you have to deselect it from Settings → Hardware → TapHome Bus. - Set proper Baudrate, Parity, Data Bits, Stop Bits and Poll Interval. In some cases, the template will set those attributes for you. Keep in mind that you can use more than one modbus device on the same BUS but they have to use the same general modbus settings (Baudrate, Parity, Data Bits, Stop Bits) and specific Slave ID for each connected device.
- Click Add From Template and select your compatible device
- When you set proper Modbus Slave ID and return back from this dialog, pre-configured devices will be created
Since both TapHome Bus and Modbus RTU are based on RS485 standard, they are not compatible. It is not possible to combine TapHome Bus device and Modbus RTU device on a single BUS.
Templates for Modbus RTU devices
| Brand | Template name | Modbus Gateway | Product Compatibility |
|---|---|---|---|
|
|
| All Atrea RD5 compatible products |
| BLOOMECO |
|
| Bloomeco OPV |
 |
|
| EM24 EM340F |
|
|
| Domat M312 PWM Domat ECIO2 Domat UC100 Thermostat |
|
|
| All Dantherm Air Recovery models |
 |
|
| Ebm-papst series 84 / 112 / 150 / 200 Lite |
 |
|
| Fronius Symo Compatibility list |
|
|
| GTD IOT 8-button touch switch |
|
|
| Dakin Compatibility list (*TapHome recommends using native integration) Daikin Compatibility list (*TapHome recommends using native integration) |
|
|
| |
|
|
| Hitachi Compatibility list |
 |
|
| Hisense Compatibility list |
|
|
| LG Compatibility list (*TapHome recommends using native integration) |
|
|
| |
|
|
| |
|
|
| |
|
|
| Toshiba Compatibility list |
|
|
| All Komfovent Recovery models |
|
|
| Jablotron Futura |
 |
|
| Nilan Compatibility list |
 |
|
| Orno OE-WE-517 |
 |
|
| DALI BUS compatible modules |
 |
|
| Sfar MOD-1TE (PT100 / PT500 / PT1000) |
 |
|
| Viessmann Vitocal 200 Viessmann Vitotronic 200 HK3B |
 |
|
| WellPro WP8026ADAM WellPro WP8027ADAM |
