Search
MENU
  • TapHome Apps
  • Expressions
  • System architecture by project type
  • Users and Permissions
  • ZigBee supported devices

    1. Sunricher

    1.1. SR ZG9101SAC-HP

    Flush mount ZigBee radio device for dimming lights. Follow the instruction in device manual. Please note, that before paring it is necessary to connect the LED light bulb to the device for proper operation. Set ZigBee gateway into pairing mode by clicking on Find new devices. Then short press Reset key for 5 times continuously or the power button on the device for 5 times continuously if the Prog key is not accessible. Connected light will blink 5 times and then stays on, then the device will appear in found devices.

    On paired module add Analog output device.

    1.2. SR ZG9080A

    ZigBee flush mount device for AC blinds control. Follow the instructions in device manual. Please note, that before pairing it is necessary to connect the blinds or slides to the device and make the position calibration. For slides, short press button K1 twice. For blinds, short press button K1 three times, calibration starts automatically.

    After the calibration, set ZigBee gateway into pairing mode and then short press button K2 five times in a row (Or reset power of the device for 5 times in a row). There shall be response from the motor that the controller is added to the network successfully. Then the device will appear in found devices.

    On paired module, add either Blind or Slide device. It is also possible to start calibration in the device service settings now.

    1.3 SR ZG9100A

    Flush mount potential free ZigBee radio switch with 1 relay. Follow the instruction in device manual. Please note, that before pairing it is necessary to connect the output device for proper operation. Set ZigBee gateway into pairing mode by clicking on Find new devices. Then, short press Reset key for 5 times in a row or re-power the device 5 times in a row if the Prog. key is not accessible. Connected light will blink 5 times and stays on, then the device will appear in found devices.

    On paired module add Digital output device.

    1.4 SR ZG2801-K2

    ZigBee push-button in frame with 4 microswitches. Follow the instruction in device manual. First, remove the device from old ZigBee network if necessary. Press and hold down the On/Off push button for at least 5 seconds until the LED indicator switches on, then immediately press the On/Off button 5 times - the LED indicators blinks several times. After this, set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold down the On/Off push button for at least 5 seconds until the LED indicator switches on, then immediately short press the Brightness button. When the LED indicators blinks several times quickly, it means that device is pairing to the ZigBee gateway and should appear in the found devices.

    On paired module add On/Off/Level control push button, Color control push button and Color temperature control push button. Please note, that physical On/Off push button on the device does not operate as long press device - this function is used to pair and reset the device. For level control, long press of brightness push button should be used.

    2. Philips hue

    Supported are Philips hue bulbs - white ambiance and white and color ambiance. In both cases, it is first necessary to remove the bulb from previous ZigBee network.

    The bulb connected to the Hue bridge is removed from the bridge via the Hue app. If it is not known where the bulb is connected, try pairing it to a Hue bridge by entering the 6 character serial number in the Philips Hue app. After this, remove it from bridge.

    Unpaired hue bulb will connect to TapHome ZigBee gateway after setting the gateway into pairing mode by clicking on Find new devices and switching on the hue bulb.

    2.1. White ambiance bulb

    On paired module add Analog output device.

    2.2. White and color ambiance

    On paired module add RGB Light device.

    3. IKEA

    3.1. TRADFRI LED bulb

    Prepare the bulb by connecting it to the power supply with on/off switch. Start with the bulb on. Set ZigBee gateway into pairing mode by clicking on Find new devices. Then, switch the bulb off and on 6 times - with short on and longer off. It is not necessary for the bulb to switch on during this impulses. At the end leave the bulb on. If correctly reset it will switch on shortly and then dim down and up until the pairing is over.

    On the paired module add Analog output device.

    3.2. TRADFRI ON/OFF switch

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press the pair button (found under the back cover next to the battery) 4 times in a row. The red light on the front side should flash a few times and the turn off. After a few seconds it turns back on and pulsates. When connected, the light turns off.

    On paired module add two push buttons - On/Level push button and Off/Level push button. Correctly works with short and long press.

    3.3. TRADFRI control outlet

    Set ZigBee into pairing mode by clicking on Find new devices. Press and hold theReset button (pinhole underneath the light, located at the top (bottom if UK) of the outlet) with a paperclip until the white light starts fading. Hold onto the button for a few more seconds, then release.

    On paired module add Digital output device.

    3.4. TRADFRI motion sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press the pair button 4 times in a row. The red light on the front side should flash a few times and the turn off. After a few seconds it turns back on and pulsates. When connected, the light turns off.

    On paired module add Reed contact. Please note, that this device never sends “no moving” event, so it is cleared automatically in TapHome Core. Also it will not send the moving event sooner than approximately one minute after previous event.

    3.5. TRADFRI signal repeater

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Push the reset button of the device with a paperclip for 5 seconds. While pairing the LED is flashing/dimming slowly. Once the pairing is finished, the LED stays on.
    There are no devices added on this module - it is just working as a repeater.

    4. Xiaomi

    4.1. Aqara temperature, humidity and pressure sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the Reset button on the device for +- 5 seconds until the blue light starts blinking. After this the device will pair with the gateway.

    On a paired module add two devices: temperature sensor and pressure sensor.

    4.2. Aqara movement and illuminance sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the Reset button on the device for +- 5 seconds until the blue light starts blinking. After this the device will pair to the gateway.

    On paired module add two devices: reed contact and brightness sensor.

    4.3. Aqara door & window contact sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the Reset button on the device for +- 5 seconds until the blue light starts blinking. After this the device will pair to the gateway.

    On paired module add Reed contact device.

    4.4. Aqara water leak sensor

    Set ZigBee gateway in pairing mode by clicking on Find new devices. Press and hold Water logo on the device for +- 10 seconds until the blue light blinks three times, release the water logo and wait. After this the device will pair to the gateway.

    On paired module add Reed contact device.

    4.5 Aqara Single Switch Module T1 (with/without neutral)

    After cabling the module switch it on after setting ZigBee gateway in pairing mode by clicking on Find new devices. If the pairing does not succeed, wait until finding procedure completely finish. Then reset the module network setting. Either hold the push button on the module for 8 seconds or when the external switch is connected, turn it on and off 5 times for resetting the network settings. The blue led on the module should blink quickly.

    Then switch off the module, start pairing mode by clicking on Find new devices and power on the module.

    On the paired module add Digital output device.

    4.6. Aqara vibration sensor

    Set ZigBee gateway in pairing mode by clicking on Find new devices. Press and hold Reset button on the device for +- 5 seconds until the blue light blinks, release the reset button and single press it each 2 seconds until the device is paired - maximally 20 times.

    On the paired module add Reed contact device.

    4.7. Aqara Smart Wall Switch H1 EU (No Neutral)

    Set ZigBee gateway in pairing mode by clicking on Find new devices. Press and hold the button on the device for +- 10 seconds (until the blue light starts blinking and stops blinking), release and wait. After this the device will pair to the gateway.

    On the paired module add two Digital output devices. After adding a second device, open service settings and change property End point ID to 2.

    4.8. Aqara Wireless Remote Switch H1 (Double Rocker WXKG02LM)

    Set ZigBee gateway in pairing mode by clicking on Find new devices. Press and hold the button on the device for +- 10 seconds (until the blue light starts blinking and stops blinking), release and wait. After this the device will pair to the gateway.

    On the paired module add two Multi state Push buttons. After adding a second device, open service settings and change property End point ID to 2.

    5. SONOFF

    5.1. Contact sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the Reset button for 5s until the LED indicator flashes three times, which means the device has entered pairing mode.

    On paired module add Reed contact device.

    5.2. Temperature and humidity sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the Reset button for 5s until the LED indicator flashes three times, which means the device has entered pairing mode.

    On a paired module add Temperature sensor device.

    5.3. Wireless button

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Press and hold the reset button for 5s until the LED indicator flashes three times, which means the device has entered pairing mode. Reset button is inside the device - so it is necessary to open the device cover.

    On paired module add Off/Level push button. Please note that this device does not support long press - on long press it is sending off command.

    5.4. Motion sensor

    Set ZigBee gateway into pairing mode by clicking on Find new devices. Previously unpaired device (brand new) will automatically enter pairing mode after power on. In other case press and hold the reset button through the small hole at the top for about 5 seconds until the light flashes several times. The device will then go into pairing mode.

    On a paired module add Reed contact device.

    5.5. ZBMini Switch Set ZigBee gateway into pairing mode by clicking on Find new devices. Previously unpaired device (brand new) will automatically enter pairing mode after power on. In other case press and hold the reset button at the top for about 5 seconds until the light flashes several times. The device will then go into pairing mode.

    On a paired module add Digital output device.

    6. Eurotronic

    6.1. Heater thermostat for radiator valve

    Follow the instructions in installation manual and first mount the thermostat to the radiator valve. Then, switch it on and let it mechanically calibrate the thermostat to the valve. Set ZigBee gateway into pairing mode by clicking on Find new devices. Hold Boost, +, and - buttons together - a count from 1 to 10 will be on the display. Release once ‘rES’ is displayed. Hit Boot once after ‘Jin’ is displayed to start pairing to the ZigBee network. Once successfully paired ‘Ins’ should be displayed and the boost button should flash green.

    On paired module add Thermostat device.

    7. SMaBiT

    7.1. Wall thermostat with Relay
    Set ZigBee gateway into pairing mode by clicking on Find new devices. Previously unpaired device (brand new) will display No NET and will enter pairing mode after holding + button until shortly Joi is displayed. In the other case, use the following reset procedure:

    To be able to register the wall thermostat in a new smart home system, it is necessary to reset it first.

    Hold both (+ and-) buttons for 5 seconds. "Pro" appears on the display. Press the "+" button as often as the word "RST" appears on the right through "Pro." Now, press both buttons again. At first, "Yes" appears on the display. The device restarts afterwards. If less than 30 seconds have elapsed since the batteries were inserted, you can skip this step.

    Hold both buttons again for 5 seconds. "Pro" appears on the display. Press the "+" button so often that the word "read" appears right through "Pro". Press both buttons again. At first, "Yes" appears on the display. The device restarts and the settings are deleted. On the screen, the message becomes "no network" instead of the temperature. You can now re-register the thermostat. If "No" appears on the display, you have waited more than 30 seconds to enter since the batteries were inserted or after the successful completion of Step 1. Please repeat the procedure from step 1.

    On a paired module add Thermostat device.

    8. Danalock

    8.1. Door lock Danalock V3 ZigBee

    You can configure the Danalock via the button found in the small hole on the top of the lock. Set ZigBee gateway into pairing mode by clicking on Find new devices. On a previously unpaired device (brand new) ones click the configuration button and the device will enter pairing mode - the LED on the device will blink green. In the other case 10 times click the configuration button to reset all settings - the LED on the device will blink red. After the correct reset enter pairing mode as described before.

    On a paired module add Door lock.

    9. POPP

    9.1. POPP Smart Thermostat for radiator valve

    Follow the instructions in the installation manual and first mount the thermostat to the radiator valve. Set ZigBee gateway into pairing mode by clicking on Find new devices. On a previously unpaired device (brand new) press the button on the POPP Smart Thermostat once. The connection symbol on the screen will start to flash. Finish the installation by pressing and holding the button for 3 seconds on POPP Smart Thermostat. Popp Smart Thermostat will finish mounting mode and will display the temperature setting on the following screen.

    If you need to pair POPP Smart Thermostat to a new Zigbee hub/gateway, you must factory reset this device before it can be paired to a new hub.

    To factory reset POPP Smart Thermostat:

    1. Remove one battery.

    2. Hold the button on the Smart Thermostat while inserting the battery. The display will start flashing if performed correctly.

    3. When the display stops flashing, release the button. The POPP Smart Thermostat is now reset to factory default.

    4. POPP Smart Thermostat will change into the mounting mode. You will see the “M” on the screen of the Smart Thermostat which indicates that you should now be able to pair your POPP Smart Thermostat to a new Zigbee hub/gateway.

    On the paired module add Thermostat device.