Search
MENU

Configuration in TapHome

SIP server for your doorbell is Core unit. Therefore it should have static IP address. TapHome tunnelling server is used to transfer audio and low framerate snapshots from camera, if you are receiving call outside local network. Multiple phone numbers can be mapped to different TapHome users or groups. Also it is possible to control relays that are located on doorbell. On Android and iOS, push notifications are received as regular VoIP phone calls.

SIP server for your doorbell is Core unit. Therefore it should have static IP address: https://taphome.atlassian.net/wiki/spaces/SUP/pages/332431441/Static+IP+address+configuration. TapHome tunnelling server is used to transfer audio and low framerate snapshots from camera, if you are receiving call outside local network. Multiple phone numbers can be mapped to different TapHome users or groups. Also it is possible to control relays that are located on doorbell. On Android and iOS, push notifications are received as regular VoIP phone calls.

Adding new IP Camera & Door bell CCU

In Settings/Hardware choose "Add new interface" and select IP Camera & Door bell CCU:

Basic parameters

After creating new CCU please set basic parameters or use default values:

For SIP coordinator choose UDP port - default value 5060.

User mappings

There is necessary to map SIP users (phone numbers) defined in Door bell to TapHome users. For this please click on SIP user mappings. There is predefined default All users - this means that any SIP phone call will be mapped to TapHome users defined for this user:

Click on default SIP user or define new SIP user and click on it - this will open following screen with user maping definition:

Choose groups which you want to map for SIP user or click on "Add new User" and select users from TapHome defined users:

After selecting user/users please return back na save the mapping changes.

Adding devices

To add IP camera or Door bell device please first set up your camera or door bell device. Follow the device settings instructions: Devices configuration:https://taphome.com/en/support/238485507.

When the device is set up, click on "ADD DEVICE" in CCU main screen.

Select from predefined types or choose Unknown device:

If the device is ONVIF enabled you will find it in the offered list of devices:

If your deice is in the list please click on it and follow next settings.

If the device is not in the list click on "ENTER IP ADDRESS" and enter device IP address in the next screen:

Device basic parameters

After adding the device the service settings for the device will be opened:

Fill the ATTRIBUTES as for any other device. Fill then at least User and Password and select Authentication type - according to device type. Please do not change this value for predefined devices. Commonly used authentication type is Digest. Ones this parameters are set click on "CHECK CONNECTION". If parameters are set correctly the device information's will be displayed:

In case the parameters are not set correctly or the IP address of the device is not set properly or device do not support ONVIF the following screen will be displayed:

Please check than again all parameters and try again to check the device connection.

Local network settings

When all previews steps was successful the valid local IP address is already defined. In case that device use diferent as default HTTP and RTPS port please set it accordingly:

Remote network settings

In case you want to use device not only in your local network there is necessary to set up remote IP address of the device. If the HTTP port and RTSP ports are routed through local router there is usually necessary to tunel these ports and set the correct tunnelled port values:

Video streams

There is possible to use two video streams from the device - for displaying the low resolution video and for displaying the high resolution video. Please select also streams type - there is necessary to use the same stream type for low and high resolution video.

Clicking on the stream will for ONVIF enabled devices list the device streams. Select from this streams or select custom stream and fill it manually:

Snapshot

Define path to snapshot for the device. This is used for example for door bell devices to store the image when the call is initialized from the device.

Again if you click on the path for ONVIF enabled devices it will display the snap shot list.

Other

Built in devices

There is possible to use built in relays - for opening the door, switching light or alarm signalling. There are two types of supported switches - HTTP switches and ONVIF switches.

For know devices the HTTP switch for door open is automatically added with the main device.

To add additional HTTP switch or ONVIF switch click on the "Add HTTP switch" or "Add ONVIF switch".

HTTP switch is always added - and you need to fill up the parameters for http command ON and command OFF and switch off timeout in case it is monostable switch:

ONVIF switches are added only if they already do not exist. ONVIF switch has so called identification token and only one switch with the same token is added automatically.

Action buttons

There is possible to configure buttons which will be displayed on the IP Camera/ Door bell main screen. Use "Add button" in ACTION BUTTONS to select the switch device from the list of devices:

Added button is than displayed in the main screen: