TapHome
Community Beta

iEAST AMP80

The iEAST AMP80 is a LinkPlay-based Wi-Fi and Bluetooth stereo streaming amplifier. TapHome controls its volume, mute, playback and input source over the local HTTP API on port 80.

Packet Parser → HTTP7 devicesRevision 1.0 Last updated: November 18, 2026

Submitted by ERMAMONT s.r.o.

iEAST AMP80

Import into the TapHome appHardware › Packet Parser › Add from template

Download Template
On this page

Network address

TapHome reaches this device at the address entered on import. Give the device a fixed address — an IP reservation in the router, or its mDNS name if it supports one — otherwise the integration stops working when the router changes the address.

Network Preparation

Integration guide

The iEAST AMP80 is a stereo streaming amplifier that drives passive 4 Ω or 8 Ω speakers and plays music over Wi-Fi (2.4 GHz), Ethernet and Bluetooth 5.0, alongside wired analog and digital inputs. It is built on the LinkPlay streaming platform, which serves an HTTP API on port 80: plain GET requests in the form http://<IP>/httpapi.asp?command=<command>, JSON responses, no login and no cloud account.

The TapHome template talks to the amplifier directly over the local network. It polls the player status every 3 seconds and provides seven devices: volume, mute, play / pause, stop, next and previous track, and input source selection.

Hardware connection

The connector positions below follow the numbering in the AMP80 product manual.

ConnectorDescription
Speaker (③)Passive speakers, 4 Ω or 8 Ω (banana plugs are included)
DC (④)Power input for the supplied adapter
IR In (⑤)External IR receiver — required to use the remote control
SUB-out (⑥)Active subwoofer
Coaxial In (⑦)Digital coaxial input for a CD/DVD player, TV and similar (AMP80 V1)
AUX In (⑧)Analog input, 3.5 mm jack
Ethernet (⑨)RJ-45, 10/100 Mbit/s — network cable to the router

The two hardware versions differ in their wired inputs: the AMP80 V1 has a coaxial digital input, while the AMP80 V2 lists an optical digital input and a USB 2.0 input next to AUX in. Check which version is installed before using the digital input from TapHome (see the input source table below).

ParameterAMP80 V1AMP80 V2
Output power, 4 Ω, 1 kHz> 80 W per channel @ 1 % THD+N> 80 W per channel @ 1 % THD+N
Output power, 8 Ω, 1 kHz> 65 W per channel @ 1 % THD+N> 60 W per channel @ 1 % THD+N
Digital inputCoaxialOptical
Supplied power adapterDC 32 V / 4.75 A (AC 100–240 V, 50/60 Hz)DC 32 V / 4.75 A (AC 100–240 V, 50/60 Hz)

The V1 manual marks the DC input itself as 24–32 V / 3.3 A; use the supplied adapter.

Mode indicator and Connect button

The AMP80 V1 manual describes the front indicator and the multi-function Connect button as follows:

IndicatorMeaning
Green, blinkingPowering on
Green, slow blinkStandby
Green, solidWi-Fi mode
Blue, solidBluetooth
White, solidAUX in
Orange, solidCoaxial in
  • Short press — switches to the next mode (input).
  • Long press for 3 s while green — Wi-Fi network configuration mode.
  • Long press for 3 s while blue — Bluetooth pairing mode.
  • Long press for 3 s while white — restores factory settings.

Network setup

Connect the power adapter first. The green indicator lights up; wait about 30 seconds until the amplifier has fully started.

Option A — Ethernet

Connect the AMP80 to the router with a network cable. The amplifier is reachable as soon as it has started; no Wi-Fi configuration is needed. For a TapHome installation, Ethernet is the recommended connection.

Option B — Wi-Fi (2.4 GHz)

  1. Install the iEAST APP on the phone or tablet (Android, iOS or HarmonyOS).
  2. Connect the phone to the 2.4 GHz Wi-Fi network the amplifier should join.
  3. Open the app. A new-device prompt appears; if it does not, put the amplifier into Wi-Fi configuration mode by holding the Connect button for 3 seconds while the indicator is green.
  4. Select the amplifier, choose the wireless network and enter its password.
  5. Follow the prompts in the app until the connection succeeds. The app may offer a firmware update, which takes a few minutes depending on the internet connection.

The AMP80 supports only the 2.4 GHz Wi-Fi band (IEEE 802.11 b/g/n) — 5 GHz networks are not supported. The network name (SSID) must not contain Chinese characters; use Latin letters or digits.

Checking the HTTP API

Open the following address in a web browser on a computer in the same network:

1
http://<IP>/httpapi.asp?command=getPlayerStatus

The amplifier answers with a JSON object. The template reads four of its fields:

FieldMeaning
volCurrent volume, 0–100
mute0 = not muted, 1 = muted
statusplay, pause, stop or load
modeCurrent source, for example 10 network, 40 line-in, 41 Bluetooth, 43 optical

A reply in the browser means the amplifier is reachable and the API is active — TapHome uses the same requests. http://<IP>/httpapi.asp?command=getStatusEx returns further device details, including the firmware version and MAC address.

Template import in TapHome

Import the template and enter the amplifier’s address in the import parameter IP adresa zariadenia (IP address of the device); port 80, plain HTTP without authentication and the 3-second polling interval are already set in the template.

Restoring factory settings

If the amplifier stops responding to the HTTP API, restore its factory settings with one of these methods:

  1. Connect button — short-press Connect to switch to line input (white indicator), then hold the button for 3 seconds until the indicator starts blinking green.
  2. IR remote control — switch to line input mode with the remote, then hold the same button for 3 seconds.
  3. iEAST APP — open the device, select Device information → Restore factory settings and confirm.

Device capabilities

The device names in the template are in Slovak; they are shown in brackets.

Volume and mute

  • Volume (Hlasitosť) — a dimmer for continuous volume control from 0 to 100 %. TapHome reads the vol field and writes the level with setPlayerCmd:vol:<0–100>.
  • Mute (Stlmenie) — a switch with the states Stlmené (muted) and Zapnutý zvuk (sound on). The state is read from the mute field (0 = sound on, 1 = muted); the commands are setPlayerCmd:mute:1 and setPlayerCmd:mute:0.

Playback control

DeviceTypeFunctionCommand
Play / pause (Prehrávanie)SwitchOn resumes playback, off pauses it. Reads as on when status is play; states Prehráva (playing) and Pozastavené (paused)setPlayerCmd:resume / setPlayerCmd:pause
Stop (Stop)Push buttonStops playbacksetPlayerCmd:stop
Next track (Ďalšia skladba)Push buttonSkips to the next tracksetPlayerCmd:next
Previous track (Predchádzajúca skladba)Push buttonReturns to the previous tracksetPlayerCmd:prev

According to the LinkPlay API documentation, stop also removes the selected source from the player. Play / pause resumes a paused stream, but after Stop it may not restart playback.

Input source

Input source (Vstupný zdroj) is a multi-value switch that switches between the amplifier’s inputs:

ValueSourcemode readCommand
Sieť (WiFi)Network streaming10setPlayerCmd:switchmode:wifi
Linkový vstupAUX in, 3.5 mm jack40setPlayerCmd:switchmode:line-in
BluetoothBluetooth audio41setPlayerCmd:switchmode:bluetooth
Optický vstupDigital input43setPlayerCmd:switchmode:optical

The value Optický vstup switches the amplifier’s digital input with the optical command and recognizes it by mode 43, which the LinkPlay documentation assigns to the optical input. That matches the optical input of the AMP80 V2. The LinkPlay API has a separate co-axial source, so on an AMP80 V1 with a coaxial input, check on the device that this value selects the coaxial input and is read back correctly.

Any other mode value — for example AirPlay, DLNA or Spotify Connect started from a phone, or the idle state — is shown as Sieť (WiFi), which is the template’s fallback value.

Other commands of the HTTP API

The same API offers more functions that the template does not use; they can be added with further devices or called from TapHome scripts:

  • Track metadata — title, artist and album in the fields Title, Artist and Album of the getPlayerStatus response, encoded as hexadecimal UTF-8 strings.
  • Multiroom — group control of several players with the multiroom:* commands.
  • Seeking — setPlayerCmd:seek:<position>, position in seconds; it has no effect on radio streams.
  • Equalizer — five presets (Normal, Classic, Pop, Jazz, Vocal) with setPlayerCmd:equalizer:<0–4>. This command is not described in the published LinkPlay documentation; check it on the device.
  • Presets — recall a stored preset with MCUKeyShortClick:<0–10>.
  • Reboot — restart the amplifier remotely with reboot.

Troubleshooting

The amplifier does not respond to HTTP requests

  1. Open http://<IP>/httpapi.asp?command=getPlayerStatus in a browser. If no JSON comes back, the problem is in the network, not in TapHome.
  2. Check that the AMP80 is in the same local network as the TapHome control unit and that no firewall blocks port 80 between them.
  3. Check the amplifier’s IP address in the router; if it has changed, correct the address in the module settings in TapHome.
  4. If the amplifier stopped responding after a firmware update, restart it — send reboot, or disconnect the power supply for a moment.
  5. As a last resort, restore the factory settings (see above).

The LinkPlay documentation notes that API responses can differ between firmware versions; getStatusEx shows which firmware the amplifier runs.

The playback state does not update

  • While a stream is loading, the player reports status load, which TapHome shows as paused — this is a transitional state.
  • The template polls the amplifier every 3 seconds, so a change made in the iEAST APP or another streaming app can take up to one polling interval to appear in TapHome.

The input source shows the wrong value

Streaming started from Spotify Connect, AirPlay or DLNA reports a mode value that does not match any of the four listed sources — the amplifier switched over by itself, and TapHome shows the fallback value Sieť (WiFi).

Wi-Fi setup fails

  • The phone must be connected to a 2.4 GHz network during setup.
  • An SSID with Chinese characters is not supported — rename it using Latin letters or digits.
  • If the app cannot find the amplifier, activate Wi-Fi configuration mode by holding Connect for 3 seconds while the indicator is green, then repeat the setup.

Available devices 7

These devices appear in TapHome after import.

iEAST AMP80 Module
Hlasitosť Dimmer

Hlasitosť

Read level
VAR r := SENDHTTPREQUEST("/httpapi.asp?command=getPlayerStatus");
IF r.IsSuccess
    RETURN(PARSEJSON(r.Content, "$.vol", true) / 100);
END
RETURN(0);
Write level
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:vol:" + ROUND(Le * 100));
Stlmenie Switch
Values / States: Stlmené · Zapnutý zvuk

Stlmenie

Read switch state
VAR r := SENDHTTPREQUEST("/httpapi.asp?command=getPlayerStatus");
IF r.IsSuccess
    RETURN(PARSEJSON(r.Content, "$.mute", true));
END
RETURN(0);
Write switch state
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:mute:" + IF(St, 1, 0));
Prehrávanie Switch
Values / States: Prehráva · Pozastavené

Prehrávanie

Read switch state
VAR r := SENDHTTPREQUEST("/httpapi.asp?command=getPlayerStatus");
IF r.IsSuccess
    VAR status := PARSEJSON(r.Content, "$.status", true);
    RETURN(IF(status = "play", 1, 0));
END
RETURN(0);
Write switch state
IF St
    SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:resume");
ELSE
    SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:pause");
END
Stop Push Button

Stop

Read button state
RETURN(0);
Write button state
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:stop");
Ďalšia skladba Push Button

Ďalšia skladba

Read button state
RETURN(0);
Write button state
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:next");
Predchádzajúca skladba Push Button

Predchádzajúca skladba

Read button state
RETURN(0);
Write button state
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:prev");
Vstupný zdroj Multi-value Switch
Values / States: Sieť (WiFi) · Linkový vstup · Bluetooth · Optický vstup

Vstupný zdroj

Read switch state
VAR r := SENDHTTPREQUEST("/httpapi.asp?command=getPlayerStatus");
IF r.IsSuccess
    VAR m := PARSEJSON(r.Content, "$.mode", true);
    RETURN(SWITCH(m, 10, 0, 40, 1, 41, 2, 43, 3, 0));
END
RETURN(0);
Write switch state
VAR src := SWITCH(Mu, 0, "wifi", 1, "line-in", 2, "bluetooth", 3, "optical", "wifi");
SENDHTTPREQUEST("/httpapi.asp?command=setPlayerCmd:switchmode:" + src);
Connection: Packet Parser → HTTP

Import parameters

Enter these values when you import the XML.

Asked in the appDefault
IP adresa zariadenia192.168.1.100

Found a problem with this device template?

Tell us what's wrong, what's missing, or how the template should behave. We rely on your feedback to keep the catalog accurate.

Template · TapHome portal iEAST AMP80 Open this template in the Customer Portal to apply it to one of your homes, or to draft a refinement and submit it back to the catalog. Packet Parser → HTTP View in TapHome portal